Lokar TC-1000LS1 36″ Hi-Tech Throttle Cable Kit for GM LS1 Engine

The cables mount nicely with Lokar's array of Brackets and Return Springs which are sold separately. It has a "u-cut-to-fit" outer housing which is available in 24 inch or 36 inch lengths with a "U-Cut-to-Fit" stainless inner wire. Aluminum ferrules/instructions/Stainless Steel Housing/Stainless Steel Aluminum Fittings;.

It has custom lengths available upon request. Hi-tech throttle cable kit; fits w/ls1/ram jet 350; u-cut-to-fit; 36 in. Incl. The kits come complete with installation instructions. The clevis is designed without cotter pins or set screws. They are designed with a specially extruded liner for extended life of the cable - not to be confused with ordinary braided brake hose.

The cables are equipped with aluminum fittings and aluminum ferrules to eliminate fraying. It adapts to factory and aftermarket pedals. Lokar 36 inch hi-tech throttle cable kit for gm ls1 engine All Lokar Hi-Tech Throttle Cables are available in either stainless steel braided housing, black stainless steel braided housing or black housing.

.

Lokar TCB-40LS1 LS1 Throttle Cable Bracket for GM Throttle Body with 3" Linkage Cam

Lokar ls1 throttle cable bracket for gm throttle body with 3 inch Linkage Cam has a billet aluminum bracket mounted to the side of the LS1 manifold and is available with a single stud for throttle only or a double stud to add a cruise control cable. Linkage cam; Brushed Finish;. Throttle cable bracket; single Stud; 3 in.

.

ICT Billet LS Heater Core Bypass Hose Coolant Crossover LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551699

Used to loop the heater hose outlets of your LS/LT engine water pump. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. Linkage cam; Brushed Finish;. Includes 1 black rubber hose. Used with vehicles that are no longer using the heater core. Heater core bypass hose     this is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory Used to loop the heater hose outlets of your LS/LT engine water pump Used with vehicles that are no longer using the heater core Compatible with all LS or LT series engines from 1998 and newer Includes 1 black rubber hose Throttle cable bracket; single Stud; 3 in.

Compatible with all LS or LT series engines from 1998 and newer.

ICT Billet LS Engine Swap M16 1.5 Adapter to 1/8 NPT Oil Pressure Sensor LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551172

Sold individually with 1 sealing washer. Linkage cam; Brushed Finish;. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Made in wichita, usa produced, Kansas from aerospace grade, billet aluminum. Compatible with: all GM LS Series Engines.

Compatible with all LS or LT series engines from 1998 and newer. Seals to the block with a sealing washer. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. Used with vehicles that are no longer using the heater core. Used to loop the heater hose outlets of your LS/LT engine water pump.

1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Includes 1 black rubber hose. Male m16-1. 5 to female 1/8"-27 npt adapter this adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine. Compatible with: all gm ls series engines oil pressure sensor adapter includes: 1 aluminum adapter, Kansas from aerospace grade, 1 sealing washer Made in Wichita, USA produced,  billet aluminum  Throttle cable bracket; single Stud; 3 in.



A-Team Performance 4-Bolt Throttle Cable Bracket Compatible with Intakes 92MM 102MM LS LSX LS1 LS2 LS3 LS6 LS7 Black

Used with vehicles that are no longer using the heater core. Ideal complement to our drive-by-cable throttle bodies. Steel construction and simplistic design. Used to loop the heater hose outlets of your LS/LT engine water pump. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Specifications:throttle opening - 105mmthrottle body bolt pattern - oe 4-bolt pattern bracket material - steel included - gaskets and hardware fitment:4-bolt lsx a-team drive-by-cable throttle bodies8101281042 4-bolt lsx a-team fabricated intake manifolds810018100281003810078104381044 APPLICATION:MAKE - PontiacENGINE TYPE - Chevrolet Small Block V8 Gen.

Throttle cable bracket; single Stud; 3 in. Specifications: 105mm throttle opening, Steel Bracket Material, OE 4-Bolt Pattern, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042. Designed to work with A-Team 92mm and 102mm throttle bodies. A-team performance 4-bolt throttle cable bracket compatible with intakes 92mm 102mm ls lsx ls1 lS2 LS3 LS6 LS7 Black OVERVIEW:-Throttle Body is Drive-by-Cable Our throttle cable bracket is the ideal compliment to our drive-by-cable throttle bodies.

Compatible with all LS or LT series engines from 1998 and newer. It's been designed to work with our 92mm and 102mm throttle bodies. Seals to the block with a sealing washer.

ICT Billet USA Made - LS Engine Transmission 4L60e Bell Housing Bolts Set Kit T56 LS1 4L80e LS1 LS3 LS2 LQ4 LQ9 LS6 L92 L99 L33 LR4 L82 L83 L84 L86 L87 LT1 L8B 551652

Includes 1 black rubber hose. Steel construction and simplistic design. Linkage cam; Brushed Finish;. Zinc coated for long lasting corrosion protection and prevents threads from seizing. Used with vehicles that are no longer using the heater core. Used to loop the heater hose outlets of your LS/LT engine water pump.

Sold individually with 1 sealing washer. Heavy duty, high strength, grade 109 bolts. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Ideal complement to our drive-by-cable throttle bodies. No washers needed with these flanged headed JIS spec bolts. Compatible with all LS or LT series engines from 1998 and newer. Specifications: 105mm throttle opening, Steel Bracket Material, OE 4-Bolt Pattern, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042.

Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings.

Spectre Performance 9781 Black 4" 90 Degree Boot

Includes coupler and two clamps. The coupler is not recommended for turbo-charged/supercharged engines. No washers needed with these flanged headed JIS spec bolts. Made in the USA bolts. This spectre intake coupler is a 4 inch to 4 inch 90 degree elbow. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. Use it to connect any 4 inch outside diameter component or air intake tube to a 4 inch outside diameter component or intake tube. Zinc coated for long lasting corrosion protection and prevents threads from seizing.

Compatible with all LS or LT series engines from 1998 and newer. Specifications: 105mm throttle opening, Steel Bracket Material, OE 4-Bolt Pattern, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042. Heavy duty, high strength, grade 109 bolts. All ict billet metric flange bolts are custom made for us, right here in the USA!!

Made from PVC.

ICT Billet LS Engine Swap M12 1.5 Adapter to 3/8 NPT Coolant Temperature Sensor Water LS1 LSX LS3 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 551179

Factory ls cylinder heads are machined with metric m12-1. 5 coolant sensor ports, so your factory Small Block Chevy sensor won't thread in to them. Use pn# 551179l for longer sensors. Made in wichita, kS from aerospace grade, USA billet aluminum. Made in the USA bolts. Ideal complement to our drive-by-cable throttle bodies.

Steel construction and simplistic design. Designed to work with A-Team 92mm and 102mm throttle bodies. Specifications: 105mm throttle opening, Steel Bracket Material, OE 4-Bolt Pattern, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042. Includes 1 black rubber hose.

This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. This adapter allows you to keep your original sensors and integrate them into your swapped LS engine. Adapter has a female 3/8" npt port,. 85" deep. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Male m12-1. 5 to female 3/8"-18 npt adapter     this adapts sbc/bbc 3/8" npt coolant temperature sensors to fit into ls series cylinder heads Compatible with: all GM LS Series Engines Made in Wichita, Kansas from aerospace grade, billet aluminum Includes: 1 aluminum adapter, USA produced, 1 sealing washer Will fit sensors with .



Russell 640940 -6 AN Male to 3/8" SAE Quick-Disconnect Male Push-On EFI Fitting

This adapter will fit all LS series engines. Adapters are sold individually, and include 1 sealing washer. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Made in wichita, Kansas from aerospace grade, usa produced, billet aluminum.

Compatible with: all GM LS Series Engines. Heavy duty, high strength, grade 109 bolts. No washers needed with these flanged headed JIS spec bolts. For competition applications where reduced weight is needed, use our lightweight ProClassic Crimp-On hose ends. Ideal complement to our drive-by-cable throttle bodies.

Use pn# 551179l for longer sensors. Made in wichita, kS from aerospace grade, USA billet aluminum. Zinc coated for long lasting corrosion protection and prevents threads from seizing. Used with vehicles that are no longer using the heater core. Throttle cable bracket; single Stud; 3 in. For racers and performance enthusiasts who want high quality plumbing that's lighter and easier to assemble than traditional braided steel hose, Russell is the perfect choice.



ICT Billet USA Made Compatible with Any LS Water Pump & Thermostat Bolt Kit LSX ICT LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 551434

Heavy duty, high strength, grade 109 bolts. 90 degree coupler for 4 inch diameter intake tubes. Includes 1 black rubber hose. No washers needed with these flanged headed JIS spec bolts. All ict billet metric flange bolts are custom made for us, right here in the USA!! Steel construction and simplistic design. No washers needed with these flanged headed JIS spec bolts.

Specifications: 105mm throttle opening, Steel Bracket Material, OE 4-Bolt Pattern, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042. Use pn# 551179l for longer sensors. Made in wichita, kS from aerospace grade, USA billet aluminum. This adapter allows you to keep your original sensors and integrate them into your swapped LS engine.

Adapter has a female 3/8" npt port,. 85" deep. Linkage cam; Brushed Finish;. Made from PVC. Water pump bolts for GM LS series engines. This adapter will fit all LS series engines.

EVIL ENERGY 6AN 90 Degree Swivel Hose End Fitting for braided fuel line Aluminum Alloy black

Compatible with all LS or LT series engines from 1998 and newer. Specifications: 105mm throttle opening, OE 4-Bolt Pattern, Steel Bracket Material, and Includes Gaskets and Hardware. Fitment: 4-bolt lsx a-team drive-by-cable throttle bodies 81012 81042. Connect oil gas line, Clutch hose, Turbo line etc. They are not compatible with PTFE Hose, E85, Fuel hose, Rubber Hose .

Multi sizes supplied:available in 4 sizes and four angles:4an, 45 degree, 10an/straight, 90 degree, 180 degree. Swivel hose end no installation instructions, 6an, 8an, detailed Installation steps look described in detail. These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.

. Made from PVC. Heavy duty, high strength, grade 109 bolts. Includes 1 black rubber hose. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Made in wichita, Kansas from aerospace grade, usa produced, billet aluminum.

Compatible with: all GM LS Series Engines.